This water pump controller is fully automatic along with manual mode. This model is suitable for the pump (the normal pump placed in overground) used to lift water from reserver to overhead tank. When the water level of overhead tank fall below a specified level (middle sensor) then the Automatic Water Level Controller turns ON the pump if the reserver tank has sufficient water(above the middle sensor). When water level of overhead tank reaches to in upper level (top sensor) then Automatic Water Level Controller turn off the pump. If the water level of reserver tank fall below the middle sensor then automatic water level controller also turn off the pump.

    This automatic water level controller is a useful device for homes, hospitals, industries, etc. This product saves water, electricity and time and helps in preventing the overflow of water from the overhead tank, enabling you to efficiently manage your water resource and prevent any wastage.

1. Saves electricity (energy), water, money, times, No man power required to ON or OFF the pump. 

2. Avoids seepage of water from roofs & walls due to overflowing tanks.

3. Easy installation-Do not require to change existing wiring

4. Low maintenance

5. Compact and elegant design

6. Fully automatic

7. Increases pump life

8. Shock proof sensors work on law of conductivity. There is no current passes through sensors. 

9. High quality carbon sensors are used. These are pure carbon, no impurities, free from oxidation, ABS plastic cover cap provided. Carbon pin, molded within Polypropylene, long life, do not require frequent cleaning or replacement.

10. Automatic Water Level controller Consume very little energy, ideal for continuous operation.

11. This automatic water level controller is microcontroller based. Due to this is more reliable.

12. This controller has a buzzer which generates buzzer sound before ON or OFF time of pump to draw the attention of user. This is for kind information.

13. This automatic water level indicator has dry run indicator. After switching ON the pump the controller checks the water level for 2 minutes. If 2nd sensor detects water level within this time then pump goes on running further. Otherwise the controller stops the pump and the dry run indicator LED glows.

14. This controller has delay circuits which delay the main power for few seconds. This feature protects the internal circuit and also pump from surge voltage during the ON of main power.

15. Due to any reason if the automatic water level controller do not work then user can operate the pump manually. This feature very useful and not require emergency servicing. To use the pump in manual mode user should keep the AUTO/MANUAL switch in MANUAL position to ON the pump and to OFF the pump user should keep this switch in OFF position.

16. Contain an emergency ON/OFF switch. This features is more important. Suppose your automatic water level controller is in AUTO mode but you want to ON the pump manually now. To do this you can keep the AUTO/MANUAL switch in MANUAL position. In this case the pump will not be switched OFF automatically. You have to switch OFF the pump manually also. This automatic water level controller provides an emergency ON/OFF switch. Using this push button switch user can either ON of OFF the pump as his/her requirement when the AUTO/MANUAL switch is in AUTO position. If you want to ON the pump then press this switch once. To OFF the pump you can press this switch again otherwise the pump will be switched OFF automatically when the tank is filled with water. This feature is useful in sometimes like during summer at morning underground water level remain much than the noon or after noon. You can ON the pump by pressing this switch. The pump will be switched OFF automatically or you can switch OFF the pump manually by pressing again.

17. Comparatively low price

18. Product warrant is 1 year

19. After the end warranty period if the automatic water level controller becomes defective then we shall repair it with minimum cost.

1. Dimension: 6”x8"X2”

2. Input Voltage: Single Phase, 230V, 50Hz

3. Output Voltage: Single Phase, 230V, 50Hz

4. Maximum Capacity: 2 HP

5. Cabinet: Plastic

6. Weight: 500 gram

7. Mounting type: Wall mount

8. No of input terminals: 03 Nos [Earth, Neutral and Phase]

9. No of output terminals: 07 [Phase, Neutral, 5 nos terminals for sensors  (G/C, OL, OH, UL and UH]

10. Type of sensors: Carbon cantact type sensor

11. Number of sensor: 06 Nos [03 Nos for Overhead tank {Reference(G), OL and OH} and 03 Nos for reservoir tank {Reference(C), UL and UH}]

12. Indicators: Power On, OL, OH, Empty for overhead tank, UL, UH, Empty for reservoir tank and Dry Run

13. Mode Selection Switch: Auto/Manual toggle switch

14. Push to On Switch: One push to ON switch for Manual ON Manaual On or Manual ON Auto OFF

15. Current flows through the sensor and water: few nano ampers (Less than 1 micro ampers)

16. Sensor voltage: DC voltage, 5V

Function of Controls and Indicators in Front Panel

1. AUTO/MAMUAL Switch: This is the mode selection switch. In AUTO mode the pump runs automatically whenever the water level of overhead tank falls below the specified level (i.e. below the middle sensor) and stops automatically when the water level of overhead tank reaches at top sensor or water level of reserver tank falls below the speicified level i.e. middle sensor. In MANUAL mode the pump is started or stopped manually.

2. DRY RUN LED: When the pump is started then automatic water level controller check the water level of overhead tank. If the controller is able to detect the water at middle sensor within 2 minutes then the controller allows the pump to run further otherwise it stops the pump and engerises the dry run led.

3. MOTOR ON LED: Glow this LED when motor is ON

4. POWER LED: Glow this LED when mains power is applied. When mains power is applied then POWER LED emits red light indicating that the system is not ready. After 3 seconds the POWER LED emits green light indicating that the system is ready for operation.

5. AUTO LED: Glows this LED when mode selection switch is in AUTO position.

6. Water level indicators for Overhead Tank: There are three LEDs for indicating water levels in overhead tank. 1. Full:- Glows this LED when the overhead tank is full with water. 2. MODERATE: - Glows this LED when the water level is between top and middle sensors of overhead tank. 3. EMPTY:- Glows this LED when water level falls below the middle sensor of overhead tank.

7. Water level indicators for Reserver Tank: There are three LEDs for indicating water levels in reserver tank. 1. Full-Glows this LED when the reserver tank is full with water. 2. MODERATE-Glow this LED when the water is between top and middle sensors of reserver tank. 3. EMPTY-Glows this LED when water level falls below the middle sensor of reserver tank.

8. Emergency ON/OFF switch: When the mode selection switch is in AUTO position, the user can ON or OFF the pump manually. This features is suitable for sometimes. Suppose your automatic water level controller is in AUTO mode and pump is in OFF condition but you want to switch ON the pump now. To do this you can keep the AUTO/MANUAL switch in MANUAL position. In this case the pump will not be switched OFF automatically. You have to switch OFF the pump manually also. This automatic water level controller provides an emergency ON/OFF switch. Using this push button switch user can either ON of OFF the pump as his/her requirement when the AUTO/MANUAL switch is in AUTO position. If you want to ON the pump then press this switch once. To switch OFF the pump you can press this switch again otherwise the pump will be switched OFF automatically when the tank is filled with water. This feature is useful in sometimes like during summer at morning underground water level remain much than the noon or after noon. You can switch ON the pump by pressing this switch. The pump will be switched OFF automatically or you can switch OFF the pump manually by pressing again.

1. Install this Automatic Water Level Controller by a electrictician who good knowledge and good skill.

2. After installation of automatic water level controller verify again the connection before energize the circuit.

3. Do not change from MANUAL mode to AUTO mode or AUTO mode to MANUAL mode when the pump is running.

Change the mode of operation only when the pump is not running. When the pump is running in manual mode and if you change to AUTO mode in this time, then pump will not stop automatically.

1 year for the date of purchase

N.B: No warranty due to overvoltage or overcurrent or lightninig

Rs 5000.00 per item

(a) Automatomatic Water Level Controller(Model No. WLC07) - 1 No

(b) Carbon cantact sensors - 3 Nos for Overhead Tank + 3 Nos for Reservoir Tank

N.B: Installation charge Rs 499/- and 3 core PVC wires @Rs23/- per meter extra

ELECTRONICS PROJECT HUB PVT. LTD.

KOLKATA, WEST BENGAL

Website: www.electronicsprojecthub.com

Email ID: electronicsprojecthub@rediffmail.com

                 electronicsprojecthub@gmail.com         

Mobile: 9073315892